HomeMy WebLinkAboutContracts & Agreements_224-2021AGREEMENT TO PERFORM NON-PROFESSIONAL SERVICES
FOR IMPROVEMENT TO PUBLIC BUILDINGS AND GROUNDS
This agreement for the provision of water distribution supervisory control and data
acquisition ("SCADA") system upgrade ("Agreement") is made and entered in this 7th day of
December, 2021 ("Effective Date"), by and between the City of Redlands, a municipal
corporation ("City") and TESCO Controls, Inc , a California corporation ("Contractor") City
and Contractor are sometimes individually referred to herein as a "Party" and, together, as the
"Parties." In consideration of the mutual promises contained herein, City and Contractor agree as
follows
11
ARTICLE 1 — ENGAGEMENT OF CONTRACTOR
City hereby engages Contractor to perform water distribution SCADA system upgrade
services for City (the "Services") The Services that Contractor shall perform are more
particularly described in Exhibit "A," titled "Scope of Services," which is attached hereto
and incorporated herein by reference
1.2 The Services shall be performed by Contractor in a professional manner, and Contractor
represents that it has the skill and the professional expertise necessary to provide the
Services to City at a level of competency presently maintained by other practicing
professional Contractors in the industry providing like and similar types of Services.
ARTICLE 2 — RESPONSIBILITIES OF CONTRACTOR
2.1 Contractor shall comply with all applicable federal, state and local laws and regulations
in the performance of the Services including, but not limited, to all applicable Labor
Code and prevailing wage laws and non-discrimination laws, including the Americans
with Disabilities Act. Pursuant to Labor Code section 1773.2, copies of the prevailing
rates of per diem wages as determined by the Director of the California Department of
Industrial Relations for each craft, classification or type of worker needed to undertake
the Services are on file at City's Municipal Utilities and Engineering Department, located
at the Civic Center, 35 Cajon Street, Suite 15A (Mailing: P 0 Box 3005), Redlands,
California 92373
2.2 Contractor acknowledges that if it violates the Labor Code provisions relating to
prevailing wages that City may enforce such provisions by withholding payments to
Contractor or its subcontractors pursuant to Labor Code section 1771 6
2.3 If Contractor executes an agreement with a subcontractor to perform any portion of the
Services, Contractor shall comply with Labor Code sections 1775 and 1777 7, and shall
provide the subcontractor with copies of the provisions of Labor Code sections 1771,
1775, 1776, 1777 5, 1813 and 1815 Contractor acknowledges that the statutory
provisions establishing penalties for failure to comply with state wage and hour laws and
to pay prevailing wages may be enforced by City pursuant to Labor Code sections 1775
and 1813
2 4 Contractor and its subcontractors shall comply with the provisions of Labor Code section
1
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
1776 regarding payroll records maintenance, certifications, retention and inspection.
2 5 Contractor acknowledges that eight (8) hours constitutes a legal day's work pursuant to
Labor Code section 1810
2 6 Contractor shall comply with the provisions of Labor Code section 1777 5 as to
apprenticeships, and Labor Code sections 1771, 1775, 1776, 1777 5, 1813 and 1815
2 7 Pursuant to Public Contract Code section 7103 5(b), Contractor offers and agrees to
assign to City all rights, title and interest in and to all causes of action it may have under
section 4 of the Clayton Act (15 U S C section 15) or under the Cartwright Act (Chapter
2 (commencing with section 16700) of Part 2 of Division 7 of the Business and
Professions Code), arising from purchases of goods, goods or materials pursuant to this
Agreement.
ARTICLE 3 — RESPONSIBILITIES OF CITY
3 1 City shall make available to Contractor information in its possession that may assist
Contractor in performing the Services
3.2 City designates John R. Harris, Municipal Utilities and Engineering Department Director,
as City's representative with respect to performance of the Services, and such person
shall have the authority to transmit instructions, receive information, interpret and define
City's policies and decisions with respect to performance of the Services.
ARTICLE 4 — PERFORMANCE OF SERVICES
4 1 Contractor shall perform and complete the Services in a prompt and diligent manner in
accordance with the schedule set forth in Exhibit "A," which is attached hereto and
incorporated herein by reference The Services shall commence as of the Effective Date
of this Agreement.
4.2 The term of this Agreement shall be for a period of one (1) year from the Effective Date
of this Agreement (the "Initial Term") The City shall have the option to extend the Initial
Term of this Agreement by one (1) additional one-year term (an "Extended Term"), on
the same terms and conditions, by providing written notice to Contractor at least thirty
(30) days prior to the expiration of the Initial Term and subsequently, at least thirty (30)
days before any Extended Team. The Initial Term and the Extended Term are hereby
collectively, referred to herein as the "Term" of this Agreement.
ARTICLE 5 — PAYMENTS TO CONTRACTOR
5 1 Contractor shall furnish a labor and material bond in the form attached hereto as Exhibit
"B," which is attached hereto and incorporated herein by reference, in an amount equal to
one hundred percent (100%) of the total compensation to be paid to Contractor pursuant to
this Agreement.
2
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
5.2 The compensation for Contractor's performance of the Services shall not exceed the
amount of three million six hundred seventy nine thousand seven hundred twenty dollars
$3,679,720) for the Services provided during the Initial Term. Should this Agreement be
extended, the compensation for Contractor's performance for the Services shall not
exceed the amount of one million eight hundred ninety nine thousand seven hundred
dollars ($1,899,700) for the Extended Term. For the Initial Term and an Extended Tenn,
City shall pay Contractor on a time and materials basis up to the not to not -to -exceed
amount in accordance with the rates specified in Exhibit "C," titled "Price and Fee Bid,"
which is attached hereto and incorporated herein by reference
5.3 Contractor shall submit monthly invoices to City describing the Services performed
during the preceding month. Contractor's invoices shall include a brief description of the
Services performed, the dates the Services were performed, the number of hours spent
and by whom. City shall pay Contractor no later than thirty (30) days after receipt and
approval by City of Contractor's invoice.
5 3 Any notice or other communication required, or which may be given, pursuant to this
Agreement, shall be in writing. Any such notice shall be deemed delivered (i) on the date
of delivery in person, (ii) five (5) days after deposit in first class registered mail, with
return receipt requested, (iii) on the actual delivery date if deposited with an overnight
courier; or (iv) on the date sent by facsimile or electronic mail transmission (including
PDF), if confirmed with a copy sent contemporaneously by first class, certified,
registered or express mail, in each case properly posted and fully prepaid to the
appropriate address set forth below, or such other address as a Party may provide notice
in accordance with this section.
CITY
City Clerk
City of Redlands
35 Cajon Street
P 0 Box 3005 (mailing)
Redlands, CA 92373
jdonaldson@cityofredlands org
(909) 798-7531
CONTRACTOR
Shain Thomas, CEO
TESCO Controls, Inc
8440 Florin Road
Sacramento, CA, 95828
sthomas@tescocontrols com
(916) 395-8800
(916) 429-2817
ARTICLE 6 — INSURANCE AND INDEMNIFICATION
6 1 The following insurance coverage required by this Agreement shall be maintained by
Contractor for the duration of its performance of the Services Contractor shall not
perform any Services unless and until the required insurance listed below is obtained by
Contractor Contractor shall provide City with certificates of insurance and endorsements
evidencing such insurance prior to commencement of the Services. Insurance pohcies
shall include a provision prohibiting cancellation or modification of the policy except
upon thirty (30) days prior written notice to City
A. Workers' Compensation and Employer's Liability insurance in the amount that meets
statutory requirements with an insurance carrier acceptable to City, or certification to
3
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
City that Contractor is self -insured or exempt from the workers' compensation laws
of the State of California. Contractor shall execute and provide City with Exhibit "D,"
titled "Workers' Compensation Insurance Certification," which is attached hereto and
incorporated herein by this reference, prior to perfotivance of the Services
B Comprehensive General Liability insurance with carriers acceptable to City in the
minimum amount of One Million Dollars ($1,000,000) per occurrence and Two
Million Dollars ($2,000,000) aggregate, for public liability, property damage and
personal injury is required. City shall be named as an additional insured and such
insurance shall be primary and non-contributing to any insurance or self-insurance
maintained by City
C Business Auto Liability coverage, with minimum limits of One Million Dollars
($1,000,000) per occurrence, combined single limit bodily injury liability and
property damage liability This coverage shall include all Contractor owned vehicles
used in connection with Contractor's provision of the Services, hired and non -owned
vehicles, and employee non -ownership vehicles City shall be named as an additional
insured and such insurance shall be primary and non-contributing to any insurance or
self-insurance maintained by City
6.2 Contractor shall defend, indemnify and hold harmless City and its elected and appointed
officials, employees and agents from and against any and all claims, losses or liability,
including attorneys' fees, arising from injury or death to persons or damage to property
occasioned by any negligent act or omission by, or the willful misconduct of, Contractor,
or its officers, employees and agents in performing the Services.
ARTICLE 7 — CONFLICTS OF INTEREST
7 1 Contractor covenants and represents that it does not have any investment or interest in
any real property that may be the subject of this Agreement or any other source of
income, interest in real property or investment that would be affected in any manner or
degree by the perfotinance of Contractor's Services. Contractor further covenants and
represents that in the performance of its duties hereunder, no person having any such
interest shall perform any Services under this Agreement.
7.2 Contractor agrees it is not a designated employee within the meaning of the Political
Reform Act because Contractor.
A. Does not make a governmental decision whether to
(i) approve a rate, rule or regulation, or adopt or enforce a City law;
(ii) issue, deny, suspend or revoke any City permit, license, application,
certification, approval, order or similar authorization or entitlement;
(iii) authorize City to enter into, modify or renew a contract;
(iv) grant City approval to a contract that requires City approval and to which
City is a party, or to the specifications for such a contract;
(v) grant City approval to a plan, design, report, study or similar item,
4
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
(vi) adopt, or grant City approval of, policies, standards or guidelines for City
or for any subdivision thereof.
B Does not serve in a staff capacity with City and in that capacity, participate in
making a governmental decision or otherwise perform the same or substantially
the same duties for City that would otherwise be performed by an individual
holding a position specified in City's Conflict of Interest Code under Government
Code section 87302.
7 3 In the event City determines that Contractor must disclose its financial interests,
Contractor shall complete and file a Fair Political Practices Commission Form 700,
Statement of Economic Interests, with the City Clerk's office pursuant to the written
instructions provided by the City Clerk.
ARTICLE 8 — GENERAL CONSIDERATIONS
8 1 In the event any action is commenced to enforce or interpret any of the terms or
conditions of this Agreement the prevailing Party shall, in addition to any costs and other
relief, be entitled to the recovery of its reasonable attorneys' fees, including fees for the
use of in-house counsel by a Party
8.2 Contractor shall not assign any of the Services, except with the prior written approval of
City and in strict compliance with the terms and conditions of this Agreement. Any
assignment or attempted assignment without such prior written consent may, in the sole
discretion of City, results in City's immediate termination of this Agreement.
8.3 Contractor is for all purposes under this Agreement an independent contractor and shall
perform the Services as an independent contractor Neither City nor any of its agents
shall have control over the conduct of Contractor or Contractor's employees, except as
herein set forth. Contractor shall supply all necessary tools and instrumentalities required
to perform the Services. Assigned personnel employed by Contractor are for its account
only, and in no event shall Contractor or personnel retained by it be deemed to have been
employed by City or engaged by City for the account of, or on behalf of City Contractor
shall have no authority, express or implied, to act on behalf of City in any capacity
whatsoever as an agent, nor shall Contractor have any authority, express or implied, to
bind City to any obligation.
8 4 This Agreement may be terminated by City, in its sole discretion, by providing not less
than five (5) days prior written notice to Contractor of City's intent to terminate If this
Agreement is terminated by City, an adjustment to Contractor's compensation shall be
made, but (i) no amount shall be allowed for anticipated profit or unperformed Services,
and (ii) any payment due Contractor at the time of teumnation may be adjusted to the
extent of any additional costs to City occasioned by any default by Contractor Upon
receipt of a termination notice, Contractor shall immediately discontinue its provision of
the Services and, within five (5) days of the date of the termination notice, deliver or
otherwise make available to City, copies (in both hard copy and electronic form, where
applicable) of project related data, design calculations, drawings, specifications, reports,
estimates, summaries and such other information and materials as may have been
5
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044,doc.jn
accumulated by Contractor m performing the Services Contractor shall be compensated
on a pro-rata basis for Services completed up to the date of termination
8 5 Contractor shall maintain books, ledgers, invoices, accounts and other records and
documents evidencmg costs and expenses related to the Services for a period of three (3)
years, or for any longer penod required by law, from the date of final payment to
Contractor pursuant to this Agreement Such books shall be available at reasonable times
for examination by City at the office of Contractor
8 6 This Agreement, including the Exhibits incorporated herein by reference, represents the
entire agreement and understanding between the Parties as to the matters contained
herem, and any pnor negotiations, written proposals or verbal agreements relating to such
matters are superseded by this Agreement Except as otherwise provided for herein, any
amendment to this Agreement shall be in writing, approved by City and signed by City
and Contractor
8 7 This Agreement shall be governed by and construed in accordance with the laws of the
State of California, without regard to its conflicts of laws provisions The Parties agree
that all actions or proceedings arising in connection with this Agreement shall be tned
and litigated only in the state courts located m San Bernardino County, Cahforma, and
the federal courts located in Riverside County, California
8 8 If one or more of the sentences, clauses, paragraphs or sections contained in this
Agreement is declared invalid, void or unenforceable by a court of competent
jurisdiction, the same shall be deemed severable from the remamder of this Agreement
and shall not affect, impair or mvandate the remammg sentences, clauses, paragraphs or
sections contained herein, unless to do so would depnve a Party of a matenal benefit of
its bargam under this Agreement
IN WITNESS WHEREOF, duly authonzed representatives of City and Contractor have
signed in confirmation of this Agreement
CITY OF REDLANDS
By��G .,,� , By
Paul T Banch, Mayor Sham Thomas, CEO
ATTEST
anne Donaldson, City Clerk
6
L \ca\djm\Agreements\Tesco Controls Agreement.NPS 2.2.FY21 0044 doc.jn
EXHIBIT "A"
SCOPE OF SERVICES
The scope of services are inclusive of the instrumentation and controls required to upgrade
thirty-one (31) sites operating within the City of Redlands' (City) water distribution system.
The new control panels, instrumentation, and services listed in the Scope of Supply below have
been quoted in conformance with the plans and specifications (section 16010) engineered for the
City's CIP Project No. 501006
Additionally, the electrical and mechanical trade work required of the new panel and
instrumentation installations is also included under TESCO's scope quoted herein. Refer to the
Scope of Supply below for a complete listing of the materials and services to be provided by
TESCO on this project.
Scope of Supply
CONTROL PANEL & INSTRUMENTATION UPGRADES
1 1 1
2330 BOOSTER PUMP STATION [RTU-801
Control Panel to include•
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 36"H x 30"W x 16"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
(2) Single -Point Door Latches with Pad -Lockable Hasps
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
• Power Failure Relay
■ EMI/RFI Power Line Filter
• 24VDC Power Supply
• (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
▪ 8-Channel Al Module
• 4-Channel AO Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
• MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
7
L.\ca\djm\Agreements\Telco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
2
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Pressure Transmitter (B-BOO PIT-61)
■ Pressure Switch (B-BOO PSH-61)
■ Flow Meter (B-BOO FIT-72)
■ (3) Intrusion Switches (B-BOO ZS-92, 93, & 94)
AGATE WELL #1 FRTU-301
Control Panel to include.
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
▪ Exterior Powder Coated
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
▪ Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Camel Tan
8
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
3
1
Instrumentation to include
■ Level Transmitter (W-AGA LT-41)
■ Pressure Transmitter (W-AGA PIT-61)
■ Pressure Switch (W-AGA PSH-61)
• Flow Meter (W-AGA FIT 71)
AIRPORT WELL#1 [RTU-31]
Motor Control Center to include
■ Pad -Mount Exterior NEMA 3R Weather Wrap Galvanized Steel
Enclosure
▪ Dimensions 90"H x 176"W x 32"D
• (3) Weather Wrap Sections
• 3-Point Door Latches with Pad -Lockable Hasps
▪ Panel Top Sunshade
• Powder Coated Camel Tan
■ Pad -Mount Interior NEMA 1 Galvanized Steel Enclosure
• 480VAC, 800A, 3-Phase, 35kAIC
▪ (5) Sections Metering, Power Distribution, ATS (Future),
Pump Controls, & RTU
Section Depth 20"
• Backpans per Layout
■ Provisions for 800A SCE Utility Meter
■ 800A Main Disconnect Breaker
■ 3-Pole Power Distribution Block
• 10kVA Transformer
■ 12-Circuit Panelboard
• Pump/RVSS Thermal Magnetic Circuit Breaker
■ 400HP ABB PSTX Reduced Voltage Soft Starter with Door -Mount HIM
• Control Power Transformer
■ Set of Pump Controls & Pilot Devices
▪ HOA Switch
• Push Buttons
• Indicator Lights
▪ Elapsed Time Meter
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
▪ Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
Yagi Directional Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
9
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.PY21-0044 doc.jn
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacles
■ Service Lights with Switches
■ Fan Kits with Filtered Louvers
■ Condensation Heaters with Thermostats
■ DIN Rails, Terminal Blocks, Distribution Breakers, Fuses, Relays,
Wires, Ground Bus Bar, & Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-AIR1 LT-41)
■ Pressure Transmitter (W-AIR1 PIT-61)
■ Pressure Switch (W-AIR1 PSH-61)
■ Flow Transmitter (W-AIR1 FIT-71)
■ Intrusion Switch (W-AIR1 ZS-92)
Arc Flash Risk Assessment to include
■ Electrical Equipment Data Collection
■ Arc Flash Report
• Single -Line Diagram
▪ Fault & Short Circuit Analysis
▪ Overcurrent Protection Device Coordination Study
• Electrical Equipment Evaluation
▪ Electrical Hazards Mitigation Analysis
• Arc Flash Incident Energy Levels & PPE Requirements
■ Electrical Equipment Safety Labels (Arc Flash & Shock Hazards)
AIRPORT WELL #2 [RTU-32]
Control Panel to include•
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 36"H x 30"W x 16"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
▪ (2) Single -Point Door Latches with Pad -Lockable Hasps
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
▪ Power Supply
▪ Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
▪ (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
10
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
5
1
Yagi Directional Antenna
▪ Lightning Arrestor
▪ Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-AIR2 LT-41)
■ Pressure Transmitter (W-AIR2 PIT-61)
■ Pressure Switch (W-AIR2 PSH-61)
■ Flow Transmitter (W-AIR2 FIT 71)
■ Intrusion Switch (W-AIR2 ZS-92)
CALIFORNIA STREET WELL [RTU-33]
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 36"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
11
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
6
1
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ (2) Level Transmitters (W-CAL LT-41 & LIT 51)
■ Pressure Transmitter (W-CAL PIT-61)
■ Pressure Switch (W-CAL PSH-61)
CHICKEN HILL WELL [RTU-341
Motor Control Center to include:
• Pad -Mount NEMA 3R Galvanized Steel Enclosure
• 480VAC, 200A, 3-Phase, 35kAIC
• Dimensions 60"H x 90"W x 20"D
▪ (3) Sections Metering / Power Distribution, Pump Controls,
& RTU
▪ 3-Point Door Latches with Pad -Lockable Hasps
▪ Panel Top Sunshade
▪ Backpans per Layout
• Powder Coated Camel Tan
▪ Provisions for 200A SCE Utility Meter
■ 200A Main Disconnect Breaker
• 3-Pole Power Distribution Block
■ 5kVA Transformer
• 12-Circuit Panelboard
■ Pump/RVSS Thermal Magnetic Circuit Breaker
• 100HP ABB PSTX Reduced Voltage Soft Starter with Door -Mount HIM
■ Control Power Transformer
■ Set of Pump Controls & Pilot Devices
• HOA Switch
El Push Buttons
• Indicator Lights
▪ Elapsed Time Meter
■ Power Failure Relay
• EMI/RFI Power Line Filter
▪ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
El Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
12
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.docjn
7
1
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacles
■ Service Lights with Switches
■ Fan Kits with Filtered Louvers
■ Condensation Heaters with Thermostats
■ DIN Rails, Terminal Blocks, Distribution Breakers, Fuses, Relays,
Wires, Ground Bus Bar, & Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-CHI LT-41)
■ Pressure Transmitter (W-CHI PIT-61)
■ Pressure Switch (W-CHI PSH-61)
■ Flow Transmitter (W-CHI FIT 71)
Arc Flash Risk Assessment to include
■ Electrical Equipment Data Collection
■ Arc Flash Report
▪ Single -Line Diagram
• Fault & Short Circuit Analysis
▪ Overcurrent Protection Device Coordination Study
• Electrical Equipment Evaluation
• Electrical Hazards Mitigation Analysis
• Arc Flash Incident Energy Levels & PPE Requirements
■ Electrical Equipment Safety Labels (Arc Flash & Shock Hazards)
CHURCH STREET WELL [RTU-35]
Control Panel Retrofit to include•
■ Preassembled Backpan (mounted within RTU section of existing MCC
enclosure)
• Dimensions 68"H x 22.5"W
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
8-Slot Backplane
• Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
▪ (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
13
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2,2.FY21-0044 doc.jn
8
9
1
1
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-CHU LT-41)
■ Pressure Transmitter (W-CHU PIT-61)
■ Intrusion Switch (W-CHU ZS-92)
COOLIE HAT FLOW MONITOR [RTU-931
Control Panel to include:
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 36"H x 30"W x 16"D
• Single Section Configuration (Exterior & Dead -Front Doors)
• (2) Single -Point Door Latches with Pad -Lockable Hasps
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Current Loop Isolator/Splitter (4-20mA Flow Signal)
■ Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
• Processor Module
▪ 16-Point DI Module
▪ 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 7" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
▪ Lightning Arrestor
▪ Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Intrusion Switch (F-COO ZS-92)
CRAFTON WELL [RTU-59]
14
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doe.jn
Motor Control Center to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ 480VAC, 400A, 3-Phase, 35kAIC
• Dimensions 72"H x 156"W x 24"D
▪ (5) Sections Utility Pull Section, Metering, Power
Distribution, Pump Controls, & RTU
• 3-Point Door Latches with Pad -Lockable Hasps
• Panel Top Sunshade
• Backpans per Layout
▪ Powder Coated Camel Tan
■ Provisions for 400A SCE Utility Meter
• 400A Main Disconnect Breaker
■ 3-Pole Power Distribution Block
■ 10kVA Transformer
■ 12-Circuit Panelboard
• Pump/RVSS Thermal Magnetic Circuit Breaker
■ 200HP ABB PSTX Reduced Voltage Soft Starter with Door -Mount HIM
■ Control Power Transformer
■ Set of Pump Controls & Pilot Devices
• HOA Switch
• Push Buttons
▪ Indicator Lights
• Elapsed Time Meter
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
▪ Power Supply
• Processor Module
▪ (2) 16-Point DI Modules
Li 16-Point DO Module
▪ 8-Channel Al Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacles
■ Service Lights with Switches
■ Fan Kits with Filtered Louvers
■ Condensation Heaters with Thermostats
■ DIN Rails, Terminal Blocks, Distribution Breakers, Fuses, Relays,
Wires, Ground Bus Bar, & Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
15
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
10
1
• Level Transmitter (W-CRA LT-41)
■ Pressure Transmitter (W-CRA PIT-61)
• Pressure Switch (W-CRA PSH-61)
■ Flow Transmitter (W-CRA FIT 71)
Arc Flash Risk Assessment to include
■ Electrical Equipment Data Collection
■ Arc Flash Report
• Single -Line Diagram
• Fault & Short Circuit Analysis
• Overcurrent Protection Device Coordination Study
• Electrical Equipment Evaluation
• Electrical Hazards Mitigation Analysis
▪ Arc Flash Incident Energy Levels & PPE Requirements
■ Electrical Equipment Safety Labels (Arc Flash & Shock Hazards)
CRESCENT & CROWN PRESSURE MONITOR (RTU-911
Control Panel to include•
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
▪ 16-Point DI Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
• C-more 7" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
16
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
12
Instrumentation to include
■ Pressure Transmitter (P-CRE PIT-61)
EAST LUGONIA WELL#3 [RTU-361
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
▪ (2) 16-Point DI Modules
▪ 16-Point DO Module
▪ (2) 8-Channel Al Modules
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-ELU3 LT-41)
■ Pressure Transmitter (W-ELU3 PIT-61)
■ Pressure Switch (W-ELU3 PSH-61)
■ Flow Transmitter (W-ELU3 FIT-71)
■ (2) Intrusion Switches (W-ELU3 ZS-92 & ZS-93)
EAST LUGONIA WELL #4 [RTU-371
Control Panel to include
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
17
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
13
1
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
• (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
▪ (2) 8-Channel Al Modules
• 4-Channel AO Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ (2) Level Transmitters (W-ELU4 LT-41 & LIT 51)
■ Pressure Transmitter (W-ELU4 PIT-61)
■ Pressure Switch (W-ELU4 PSH-61)
■ Chlorine Analyzer (W-ELU4 AIT-81)
■ (2) Intrusion Switches (W-ELU4 ZS-92 & ZS-93)
EAST LUGONIA WELL #6 [RTU-38]
Control Panel to include
• Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
▪ Backpan per Layout
▪ Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
18
L.\ca\djm\Agreements\Telco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
14
1
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
• Modicon M340 PLC
▪ 8-Slot Backplane
▪ Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
▪ 16-Point DO Module
▪ (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
• (2) Level Transmitters (W-ELU6 LT-41 & LIT-51)
■ Pressure Transmitter (W-ELU6 PIT-61)
■ Flow Transmitter (W-ELU6 FIT 71)
■ Chlorine Analyzer (W-ELU6 AIT-81)
HOG CANYON WELL#2 [RTU-39]
Control Panel to include
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
o Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
▪ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
• Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
19
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 docjn
15
1
16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
• C-more 12" Touchscreen OIT
• 5-Port Unmanaged Ethernet Switch
• GFCI Convenience Receptacle
• Service Light with Switch
• Fan Kit with Filtered Louvers
• Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Radio Panel to include:
• Wall -Mount NEMA 3R Aluminum Enclosure
• Dimensions 20"H x 20.5"W x 12"D
• Single Section Configuration
• Single -Point Door Latch with Pad -Lockable Hasp
▪ Panel Top & Front Sunshades
Backpan per Layout
▪ Exterior Powder Coated Autumn White
• Circuit Breaker
• MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
• Filtered Louvers
■ DIN Rail, Terminal Blocks, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-HOG2 LT-41)
■ Pressure Transmitter (W-HOG2 PIT-61)
• Pressure Switch (W-HOG2 PSH-61)
• Flow Transmitter (W-HOG2 FIT 71)
MADEIRA WELL [RTU-401
Control Panel to include
• Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
• Exterior Powder Coated Camel Tan
• Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
• 24VDC Power Supply
20
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
16
1
• (2) 12VDC Backup Batteries & Charger
• Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
• (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
• MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
• 5-Port Unmanaged Ethernet Switch
• GFCI Convenience Receptacle
• Service Light with Switch
• Fan Kit with Filtered Louvers
• Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-MAD LT-41)
■ Pressure Transmitter (W-MAD PIT-61)
■ Pressure Switch (W-MAD PSH-61)
• Flow Meter (W-MAD FIT-71)
• (4) Intrusion Switches (W-MAD ZS-92, ZS-93A, ZS-93B, & ZS-93C)
MAGUET WELL #2 FRTU-411
Motor Control Center to include.
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• 480VAC, 200A, 3-Phase, 35kAIC
▪ Dimensions 60"H x 108"W x 20"D
• (4) Sections Metering / Power Distribution, ATS (Future),
Pump Controls, & RTU
• 3-Point Door Latches with Pad -Lockable Hasps
▪ Panel Top Sunshade
• Backpans per Layout
• Powder Coated Camel Tan
■ Provisions for 200A SCE Utility Meter
• 200A Main Disconnect Breaker
• 3-Pole Power Distribution Block
■ 5kVATransformer
• 12-Circuit Panelboard
▪ Well Pump Motor MCP Breaker
• NEMA Size 3 FVNR Starter
▪ Control Power Transformer
• Set of Pump Controls & Pilot Devices
21
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
17
1
• HOA Switch
• Push Buttons
• Indicator Lights
• Elapsed Time Meter
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
• (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
• (2) 8-Channel Al Modules
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
▪ Yagi Directional Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacles
■ Service Lights with Switches
■ Fan Kits with Filtered Louvers
■ Condensation Heaters with Thermostats
■ DIN Rails, Terminal Blocks, Distribution Breakers, Fuses, Relays,
Wires, Ground Bus Bar, & Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ (2) Level Transmitters (W-MAG2 LT-41 & LIT 51)
■ Pressure Transmitter (W-MAG2 PIT-61)
■ Pressure Switch (W-MAG2 PSH-61)
• Flow Transmitter (W-MAG2 FIT 71)
■ Chlorine Analyzer (W-MAG2 AIT-81)
■ (4) Intrusion Switches (W-MAG2 ZS-92, ZS-93A, ZS-93B, & ZS-93C)
Arc Flash Risk Assessment to include
■ Electrical Equipment Data Collection
■ Arc Flash Report
• Single -Line Diagram
• Fault & Short Circuit Analysis
▪ Overcurrent Protection Device Coordination Study
▪ Electrical Equipment Evaluation
▪ Electrical Hazards Mitigation Analysis
• Arc Flash Incident Energy Levels & PPE Requirements
■ Electrical Equipment Safety Labels (Arc Flash & Shock Hazards)
MENTONE ACRES WELL #2 FRTU-421
22
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
Motor Control Center to include:
■ Pad -Mount Exterior NEMA 3R Weather Wrap Galvanized Steel
Enclosure
• Dimensions 90"H x 140"W x 32"D
• (2) Weather Wrap Sections
3-Point Door Latches with Pad -Lockable Hasps
• Panel Top Sunshade
▪ Powder Coated Camel Tan
■ Pad -Mount Interior NEMA 1 Galvanized Steel Enclosure
• 480VAC, 800A, 3-Phase, 35kAIC
• (4) Sections. Metering, Power Distribution, Pump Controls,
& RTU
• Section Depth 20"
• Backpans per Layout
■ Provisions for 800A SCE Utility Meter
■ 800A Main Disconnect Breaker
■ 3-Pole Power Distribution Block
■ 10kVA Transformer
■ 12-Circuit Panelboard
■ Pump/RVSS Thermal Magnetic Circuit Breaker
■ 300HP ABB PSTX Reduced Voltage Soft Starter with Door -Mount HIM
■ Control Power Transformer
■ Set of Pump Controls & Pilot Devices
▪ HOA Switch
• Push Buttons
▪ Indicator Lights
▪ Elapsed Time Meter
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
▪ Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacles
■ Service Lights with Switches
■ Fan Kits with Filtered Louvers
■ Condensation Heaters with Thermostats
■ DIN Rails, Terminal Blocks, Distribution Breakers, Fuses, Relays,
23
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
18
1
Wires, Ground Bus Bar, & Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-MEN2 LT-41)
■ Pressure Transmitter (W-MEN2 PIT-61)
■ Flow Transmitter (W-MEN2 FIT 71)
■ Intrusion Switch (W-MEN2 ZS-92)
Arc Flash Risk Assessment to include
■ Electrical Equipment Data Collection
■ Arc Flash Report
• Single -Line Diagram
• Fault & Short Circuit Analysis
Overcurrent Protection Device Coordination Study
• Electrical Equipment Evaluation
▪ Electrical Hazards Mitigation Analysis
• Arc Flash Incident Energy Levels & PPE Requirements
■ Electrical Equipment Safety Labels (Arc Flash & Shock Hazards)
MENTONE & CRAFTON VALVE VAULT [RTU-85]
Control Panel to include.
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
▪ Panel Top & Rear Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
▪ 16-Point DI Module
▪ 8-Channel Al Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 7" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
24
L,\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ (2) Pressure Transmitters (V-MEN PIT-61 & PIT-62)
■ (2) Flow Meters (V-MEN FIT 71 & FIT 72)
MILL CREEK WELL#2 [RTU-43]
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
3-Point Door Latch with Pad -Lockable Hasp
▪ Backpan per Layout
▪ Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
8-Slot Backplane
▪ Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
• C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Access Point Radio
• Omni Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
• Cellular Modem
■ 8-Port Managed Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Power Distribution Equipment to include
■ 5kVA Mini Power Zone (480V 120/240V, 1-Phase)
Instrumentation to include
• Level Transmitter (W-MIL2 LT-41)
25
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
20
21
1
1
• Pressure Switch (W-MIL2 PSH-61)
• Flow Transmitter (W-MIL2 FIT-71)
• Intrusion Switch (W-MIL2 ZS-92)
MILL CREEK WELL #2A [RTU-441
Control Panel to include.
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
▪ Panel Top & Rear Sunshades
• Backpan per Layout
▪ Exterior Powder Coated Camel Tan
• Circuit Breakers as required
■ Power Failure Relay
• EMI/RFI Power Line Filter
• 24VDC Power Supply
• (2) 12VDC Backup Batteries & Charger
• Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
▪ Screw Terminal Strips & Slot Covers as required
• C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
• 5-Port Unmanaged Ethernet Switch
• GFCI Convenience Receptacle
■ Service Light with Switch
• Fan Kit with Filtered Louvers
• Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Power Distribution Equipment to include
■ 5kVA Mini Power Zone (480V-120/240V, 1-Phase)
Instrumentation to include
• Level Transmitter (W-MIL2A LT-41)
• Pressure Switch (W-MIL2A PSH-61)
• Flow Transmitter (W-MIL2A FIT 71)
MILL CREEK WELL #4 [RTU-451
Control Panel to include
• Pad -Mount NEMA 3R Galvanized Steel Enclosure
26
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
▪ Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
▪ 16-Point DO Module
▪ 8-Channel Al Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
• MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Power Distribution Equipment to include
■ 5kVA Mini Power Zone (480V 120/240V, 1-Phase)
Instrumentation to include
■ Level Transmitter (W-MIL4 LT-41)
■ Pressure Switch (W-MIL4 PSH-61)
■ Flow Transmitter (W-MIL4 FIT 71)
■ Intrusion Switch (W-MIL4 ZS-92)
22
1
MUNI WELL [RTU-471
Control Panel to include•
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
▪ 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
27
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
23
1
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Interposing Relays & Current Loop Isolators/Splitters as required
(duplication of site monitored signals)
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
• 16-Point DO Module
▪ (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-MUN LT-41)
■ Pressure Transmitter (W-MUN PIT-61)
■ Pressure Switch (W-MUN PSH-61)
■ Intrusion Switch (W-MUN ZS-92)
NEW YORK STREET WELL ERTU-581
Control Panel to include•
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 36"H x 30"W x 16"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
• (2) Single -Point Door Latches with Pad -Lockable Hasps
• Backpan per Layout
Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
28
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
24
1
▪ 8-Slot Backplane
• Power Supply
▪ Processor Module
▪ (2) 16-Point DI Modules
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-NYS LT-41)
■ Pressure Transmitter (W-NYS PIT-61)
■ Pressure Switch (W-NYS PSH-61)
■ Flow Meter (W-NYS FIT 71)
■ Intrusion Switch (W-NYS ZS-92)
ORANGE STREET WELL [RTU-50]
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
(2) 16-Point DI Modules
• 16-Point DO Module
▪ (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
29
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-ORA LT-41)
■ Pressure Transmitter (W-ORA PIT-61)
▪ Flow Meter (W-ORA FIT 72)
■ Intrusion Switch (W-ORA ZS-92)
REDLANDS HEIGHTS WELL FRTU-511
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 72"H x 36"W x 18"D
Single Section Configuration (Exterior & Dead -Front Doors)
• 480/120VAC Safety Barrier
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
• Backpan per Layout
Exterior Powder Coated Camel Tan
■ 3kVATransformer
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
• 16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ 8-Port Managed Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
30
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.docjn
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Radio Panel to include:
■ Wall -Mount NEMA 3R Aluminum Enclosure
• Dimensions 20"H x 20.5"W x 12"D
• Single Section Configuration
• Single -Point Door Latch with Pad -Lockable Hasp
▪ Panel Top & Front Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Autumn White
■ Circuit Breakers as required
• MDS Orbit 150MHz Remote Radio
▪ Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
• Pole Mounting Kit
• Cable Grounding & Weatherproofing
■ Cellular Modem
▪ Omni Antenna
• Lightning Arrestor
• Coaxial Cable as required
▪ Pole Mounting Kit
• Cable Grounding & Weatherproofing
■ Filtered Louvers
■ DIN Rail, Terminal Blocks, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
I/O Radio Panel to include:
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 30"H x 24"W x 12"D
• Single Section Configuration
▪ (2) Single -Point Door Latches with Pad -Lockable Hasps
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
• MDS Orbit 150MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
▪ Coaxial Cable as required
▪ Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
▪ Cable Grounding & Weatherproofing
■ Moxa Ethernet Remote I/O Module
■ 5-Port Unmanaged Ethernet Switch
• GFCI Convenience Receptacle
■ Filtered Louvers
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
31
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc jn
26
1
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Antenna Mast to include
■ 30' Universal Aluminum Tower with 4' Base (Foundation &
Installation by Others)
■ Tower & Base Hinged Assembly (mast fold down capability)
Instrumentation to include
■ Level Transmitter (W-RED LT-41)
■ Flow Transmitter (W-RED FIT 71)
REES WELL FRTU-521
Control Panel to include
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
▪ Dimensions 72"H x 30"W x 18"D
▪ Single Section Configuration
• 3-Point Door Latch with Pad -Lockable Hasp
• Backpan per Layout
▪ Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
▪ Power Supply
▪ Processor Module
• (3) 16-Point DI Modules
▪ 16-Point DO Module
• (3) 8-Channel Al Modules
▪ 4-Channel AO Module
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W-REE LT-41)
32
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
■ (4) Pressure Transmitters (W-REE PIT-61, PIT-62, PIT-63A, & PIT-63B)
■ (3) Differential Pressure Transmitters (W-REE DPIT-64A, DPIT-64B, &
DPIT-65)
■ (3) Intrusion Switches (W-REE ZS-84, ZS-92, & ZS-93)
TATE WATER TREATMENT PLANT
Main PLC Control Panel Retrofit to include
■ Modicon M580 PLC (Main)
▪ 2-Rack Configuration with X80 Backplane Expander Kit
— 12 Slot Backplane
— 8-Slot Backplane
• (2) AC Power Supplies
• M580 Level 2 CPU
• (2) 16-Point Digital Input Modules (AC)
▪ (2) 32-Point Digital Input Modules (DC)
• (2) 16-Point Digital Output Modules (Relay/NO)
• (3) 8-Channel Analog Input Modules (Isolated)
• (3) 4-Channel Analog Output Modules (Isolated)
▪ Removable Terminal Blocks, Prewired Cables, & Spare Slot
Covers as required
■ 8-Port Managed Ethernet Switch
■ EMI/RFI Power Line Filter
■ 1500VA Uninterruptable Power Supply
■ 24VDC Power Supply
■ DIN Rails, Terminal Blocks, Circuit Breakers, Fuses, Relays, Wires,
Ground Bus Bar, & Nameplates/Labels as required
**includes prefabrication, assembly, wiring, & factory testing**
R1O-1 Panel Retrofit to include
■ Modicon X80 Remote I/O (Drop 1)
8-Slot Backplane
• AC Power Supply
• X80 Ethernet I/O Drop Adapter
• 32-Point Digital Input Module (DC)
▪ 16-Point Digital Output Module (Relay/NO)
▪ 8-Channel Analog Input Module (Isolated)
• (2) 4-Channel Analog Output Modules (Isolated)
• Removable Terminal Blocks, Prewired Cables, & Spare Slot
Covers as required
■ EMI/RFI Power Line Filter
■ 1500VA Uninterruptable Power Supply
■ 24VDC Power Supply
■ DIN Rails, Terminal Blocks, Circuit Breakers, Fuses, Relays, Wires,
Ground Bus Bar, & Nameplates/Labels as required
**includes prefabrication, assembly, wiring, & factory testing**
RIO-2 Panel Retrofit to include
■ Modicon X80 Remote I/O (Drops 2 & 3)
• 3-Rack Configuration with X80 Backplane Expander Kit
— (2) 12-Slot Backplanes
— 8-Slot Backplane
• (3) AC Power Supplies
33
L:\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
28
1
▪ (2) X80 Ethernet I/O Drop Adapters
▪ (14) 16-Point Digital Input Modules (AC)
▪ (4) 16-Point Digital Output Modules (DC)
▪ (5) 8-Channel Analog Input Modules (Isolated)
• (6) 4-Channel Analog Output Modules (Isolated)
• Removable Terminal Blocks, Prewired Cables, & Spare Slot
Covers as required
■ EMI/RFI Power Line Filter
■ 1500VA Uninterruptable Power Supply
■ (2) 24VDC Power Supplies
■ DIN Rails, Terminal Blocks, Circuit Breakers, Fuses, Relays, Wires,
Ground Bus Bar, & Nameplates/Labels as required
**includes prefabrication, assembly, wiring, & factory testing**
WABASH & 1-10 PRESSURE MONITOR [RTU-921
Control Panel to include
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 72"H x 36"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
• 480/120VAC Safety Barrier
▪ Splash Guard
▪ 3-Point Door Latch with Pad -Lockable Hasp
▪ Panel Top & Rear Sunshades
▪ Backpan per Layout
▪ Exterior Powder Coated Camel Tan
■ 3kVA Transformer
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
• Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
• Processor Module
▪ 16-Point DI Module
▪ 16-Point DO Module
• 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 7" Touchscreen OIT
• Cellular Modem
■ 8-Port Managed Ethernet Switch
■ GFCI Convenience Receptacle
• Service Light with Switch
■ Fan Kit with Filtered Louvers
• Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
• Pressure Transmitter (P WAB PIT-61)
34
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
29
30
1
1
WELL #34 [RTU-531
Control Panel to include
■ Wall -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 36"H x 30"W x 16"D
• Single Section Configuration
• (2) Single -Point Door Latches with Pad -Lockable Hasps
• Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
▪ 8-Slot Backplane
• Power Supply
• Processor Module
• 16-Point DI Module
▪ 8-Channel Al Module
• Screw Terminal Strips & Slot Covers as required
■ C-more 7" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Pressure Transmitter (W WELL34 PIT-61)
■ Chlorine Analyzer (W WELL34 AIT-81)
■ (2) Intrusion Switches (W WELL34 ZS-92 & ZS-93)
WELL #38 [RTU-561
Control Panel to include:
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
▪ Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Panel Top & Rear Sunshades
▪ Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
35
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
31
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
▪ 16-Point DO Module
• (2) 8-Channel Al Modules
▪ Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
▪ Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W WELL38 LT-41)
■ Pressure Transmitter (W WELL38 PIT-61)
■ Pressure Switch (W-WELL38 PSH-61)
■ Flow Meter (W WELL38 FIT 72)
■ (4) Intrusion Switches (W WELL38 ZS-92, ZS-93, ZS-94, & ZS-95)
WELL #39 [RTU-571
Control Panel to include
■ Pad -Mount NEMA 3R Galvanized Steel Enclosure
• Dimensions 60"H x 30"W x 18"D
• Single Section Configuration (Exterior & Dead -Front Doors)
• 3-Point Door Latch with Pad -Lockable Hasp
• Backpan per Layout
• Exterior Powder Coated Camel Tan
■ Circuit Breakers as required
■ Power Failure Relay
■ EMI/RFI Power Line Filter
■ 24VDC Power Supply
■ (2) 12VDC Backup Batteries & Charger
■ Modicon M340 PLC
• 8-Slot Backplane
• Power Supply
• Processor Module
• (2) 16-Point DI Modules
36
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc jn
32
Lot
• 16-Point DO Module
• (2) 8-Channel Al Modules
• Screw Terminal Strips & Slot Covers as required
■ C-more 12" Touchscreen OIT
■ MDS Orbit 900MHz Remote Radio
• Yagi Directional Antenna
• Lightning Arrestor
• Coaxial Cable as required
• Pole Mounting Kit (Antenna Mast/Pole supplied by Others)
• Cable Grounding & Weatherproofing
■ 5-Port Unmanaged Ethernet Switch
■ GFCI Convenience Receptacle
■ Service Light with Switch
■ Fan Kit with Filtered Louvers
■ Condensation Heater with Thermostat
■ DIN Rails, Terminal Blocks, Fuses, Relays, Wires, Ground Bus Bar, &
Nameplates/Labels as required
**includes panel fabrication, assembly, wiring, & factory testing**
Instrumentation to include
■ Level Transmitter (W WELL39 LT-41)
■ Pressure Transmitter (W WELL39 PIT-61)
■ Pressure Switch (W-WELL39 PSH-61)
■ Flow Transmitter (W WELL39 FIT 71)
■ Flow Meter (W WELL39 FIT 72)
■ (4) Intrusion Switches (W WELL39 ZS-92, ZS-93, ZS-94, & ZS-95)
Professional Services to include:
■ Project Management
▪ project initiation, contract administration, schedule of
values, decision & submittal logs, project scheduling &
coordination, planning & resource loading, and payment
applications & billings
■ Engineering
• engineered bill of materials, engineered shop drawings,
equipment schematics, engineered submittals, technical
data, as -built documentation, and project records
• Tate Water Treatment Plant
review with the City the latest as -installed
drawings revised by TESCO (T-42335XA) for the
Main, RIO-1, and RIO-2 PLC control panels at the
Tate WTP and determine the I/O points to be
integrated with the new PLC hardware, identify
new, remaining, and to be removed I/O
■ PLC/OIT Programming
• program each local M340 PLC and C-more OIT based on the
monitoring/control requirements of each site
— coordinate technical workshops with the City as
required to fully define individual site process
controls
• utilize program standards developed during Phase 1 of the
City's CIP Project No 71349 (T-37335X1/3)
37
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044 doc.jn
Tate Water Treatment Plant
— conduct a technical workshop with the City to
redefine the control logic required of the new PLC
hardware and to be programmed to the M580 and
X80 I/O platform
— coordinate with the Project Engineer and the City
to confirm the updated I/O list and requirements
for each control panel
— program the new M580 PLC as required of the Tate
WTP process control areas and according to the
logic requirements defined through the technical
workshop
— provide the SCADA Programmer with a revised I/O
list and mapping of the PLC registers to facilitate
the reassignment of SCADA tags
— verify the newly developed PLC program functions
properly and correctly executes automated control
of the plant processes
• SCADA Programming
• modify the existing Wonderware InTouch SCADA
application hosted at the HAWC and Tate WTP facilities as
required to conform with the screen/graphics standards
developed during the Phase 1 project
▪ verify the SCADA tag database aligns with the registers of
the new M340 PLCs
▪ Tate Water Treatment Plant
— reassign the Wonderware InTouch SCADA tags as
required to accommodate the upgraded PLC
program at the Tate WTP
— modify the SCADA tag database as required to
align with the updated I/O points
— implement the required SCADA updates and
modifications across both Wonderware InTouch
applications hosted at the HAWC (primary) and
Tate WTP (secondary) facilities
— verify communications are maintained between
the Wonderware SCADA system and the upgraded
M580 PLC platform
■ Networking/Communications/Telemetry
▪ configure each radio and cellular modem required for
establishing communications with the existing high-speed
backbone network
• test and verify that the new radio/cellular links
communicate reliably
• Tate Water Treatment Plant
— assist with any protocol conversions required to
maintain communications between the PLC and
SCADA networks
— configuration of the managed Ethernet switch to
be equipped with the main PLC control at the Tate
WTP
■ Field Service / Product Startup
38
L.\ca\djm\Agreements\Tesco Controls Agreement,NPS-2.2.FY21-0044.doc.jn
33
34
Lot
Lot
• product quality review, verification of installation,
parameter/configuration adjustments as required, software
upload/download as required, instrument/device signal
spanning, function checks, and startup
• Tate Water Treatment Plant
— retrofit the new M580 and X80 I/O PLC hardware
within the existing Main, RIO-1, and RIO-2 control
panels at the Tate WTP
— rewire between the new PLC hardware and
existing panel terminal blocks as required of the
updated I/O layout
■ Onsite Training
■ O&M Manuals
Electrical Contractor (Hydrotech Electric) Installation Services to
include
■ selective electrical demolition as depicted on the engineered
plans/drawings
■ disposal of equipment not salvaged by the City
■ installation of TESCO-furnished equipment as depicted on the
drawings, including the following•
• MCCs
• Mini Power Zones
• Wall -Mount RTU Panels
▪ Pedestal/Pad-Mount RTU Panels
• Radio Panels
• Pressure Switches, Limit Switches, Level Transmitters, &
Pressure Transmitters
• Yagi & Omni Antennas
■ stainless steel stanchions for electrical boxes and enclosures
furnished by Hydrotech Electric
■ conduits, boxes, and wiring as depicted on the drawings
■ temporary signal wiring to the existing MOSCAD RTUs as required
• grounding system as indicated on the drawings or as required by
local codes and NEC
■ excavation, backfill, and compaction for equipment and conduit
installations as required
■ concrete pads as required for the new MCCs and RTU pedestals
■ saw cutting, removal, and replacement of concrete as required for
equipment and conduit installations
■ foundation construction for TESCO-furnished 30' tower at Redlands
Heights Well
• supply and install of (1) 25' antenna pole for Mill Creek Well 2A with
concrete foundation
■ supply and install of (27) 15' tall, 2" diameter GRC antenna masts
■ assistance with startup, commissioning, and testing of TESCO-
furnished equipment
Mechanical Contractor (Schuler Constructors) Installation Services to
include
■ installation of TESCO-furnished flow meters and pressure/level
instrumentation
■ supply and installation of (9) Cla-Val control valves on pump-to-
39
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
waste pipelines, including valve limit/position switches
■ supply and installation of (2) AUMA motorized actuators and valves
on pump -to -waste pipelines, including valve limit/position switches
■ supply and installation of (2) check valves on discharge pipelines
■ relocate (3) existing check valves on discharge pipelines
■ 3/4" taps and 30001b carbon steel half couplings as required of
pipeline valves and TESCO-furnished instrumentation
■ concrete pads and pipe supports as required for instrumentation
installs and pipeline modifications
■ loose flanges, nuts, bolts, and gaskets as required of the new control
valve installations
35 Lot Payment & Performance Bond (2-Year Project Duration)
40
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
Premium for Contract Term Subject to Bond No CA4128396
Adjustments Based on Final Contract Price Premium $38,433 00
EXHIBIT "B"
LABOR AND MATERIAL BOND
Whereas, the City of Redlands, State of California, and TESCO Controls, Inc (hereinafter designated
as "Principal") have entered into an agreement (the "Agreement") whereby Principal agrees to CIP Water
Distribution SCADA System Upgrade (the "Work"), which said agreement, dated December 7, 2021, and
titled as "Agreement to Perform Non -Professional Services for Improvement to Public Builds and Grounds" is
hereby referred to and made a part hereof, and
Whereas, under the terms of the Agreement, Principal is required before commencing the performance
of the Work, to file a good and sufficient Labor and Material bond with the City of Redlands to secure the
claims to which reference is made m Title 3 (commencing with Section 9550) of Part 6 of Division 4 of the
Civil Code of the State of California
Now, therefore, said Principal and the undersigned as corporate surety, are held firmly bound unto the
City and all contractors, subcontractors, laborers, material men and other persons employed in the performance
of the Agreement and referred to in the aforesaid Code of Civil Procedure in the sum of five million seventy
two thousand two hundred dollars ($5,072,200) for materials furnished or labor thereon of any kmd, or for
amounts due under the Unemployment Insurance Act with respect to such work or labor, that said surety will
pay the same in an amount not exceeding the amount hereinabove set forth, and also in case suit is brought
upon this bond, will pay, in addition to the face amount thereof, costs and reasonable expenses and fees,
includmg reasonable attomeys' fees, incurred by the City in successfully enforcing such obligation, to be
awarded and fixed by the court, and to be taxed as costs and to be included m the judgment therein rendered
It is hereby expressly stipulated and agreed that this bond shall insure to the benefit of any and all
persons, companies and corporations entitled to file claims under Title 3 (commencing with Section 9550) of
Part 6 of Division 4 of the Civil Code, so as to give a right of action to them or their assigns in any suit brought
upon this bond
Should the condition of this bond be fully performed, then this obligation shall become null and void,
otherwise it shall be and remain m full force and effect
The surety hereby stipulates and agrees that no change, extension of time, alteration or addition to the
terms of the Agreement or the specifications accompanymg the same shall in any manner affect its obligations
on this bond, and it does hereby waive notice of any such change, extension of time, alteration or addition
In witness whereof, this mstrument has been duly executed by the Principal and surety above named,
on December 2 , 2021
(SEAL)
Tesco Controls, Inc
(Contract
(Signature) SHftrIM THOMAS/ ao
(Seal and Notarial Acknowledgment of
Surety)
(SEAL)
Great American Insura
(Surety)
BY
e Co
(Signature) ( 1 Elizabeth Collodi Attorney in Fact
Address
301 E Fourth Street
Cincinnati, OH 45202
Telephone( 530 ) 895-1010
41
L \ca\djm\Agreements\Tesco Controls Agreement.NPS 2.2.FY21 0044.doc in
Issued in duplicate original
ACKNOWLEDGMENT
A notary public or other officer completing this
certificate verifies only the identity of the individual
who signed the document to which this certificate is
attached, and not the truthfulness, accuracy, or
validity of that document
State of California
County of Sacramento
On December 3, 2021 before me, Allison K Hunter, Notary Public
(insert name and title of the officer)
personally appeared Shain Thomas, CEO
who proved to me on the basis of satisfactory evidence to be the person(s) whose name(s) is/are
subscribed to the within instrument and acknowledged to me that he/she/they executed the same in
his/her/their authorized capacity(ies), and that by his/her/their signature(s) on the instrument the
person(s), or the entity upon behalf of which the person(s) acted, executed the instrument
I certify under PENALTY OF PERJURY under the laws of the State of California that the foregoing
paragraph is true and correct
WITNESS my hand and official seal
Signature __C_) I ` . LfL.4J\_- (Seal)
ALLISON K HUNTER
Notary Public California
Sacramento County E
Commission # 2357076 i
My Comm Expires May 11, 2025
ACKNOWLEDGMENT
A notary public or other officer completing this
certificate verifies only the identity of the individual
who signed the document to which this certificate is
attached, and not the truthfulness, accuracy, or
validity of that document
State of California
County of Sacramento
On December 2, 2021 before me, Hunter Smithson, Notary Public
personally appeared
who proved to me on the basis of satisfactory evidence to be the person(-) whose name(s} is/a-e
subscribed to the within instrument and acknowledged to me that 4e/she/thcy executed the same in
his/her/thcir authorized capacity(ies), and that by la-is/her/their signatures} on the instrument the
person(6)7 or the entity upon behalf of which the person(s} acted, executed the instrument
(insert name and title of the officer)
Elizabeth Collodi
I certify under PENALTY OF PERJURY under the laws of the State of California that the foregoing
paragraph is true and correct
WITNESS my hand and official seal
Signature
(Seal)
HUNTER SMrTHS0N
°COMM # 2372866
NOTARY PUBLIC CALIFORNIA
COUNTY OF SACRAMENTO_
1 �~ Comm Expires -AUG 29, 2025
e•
GREAT AMERICAN INSURANCE COMPANY®
Administrative Office 301 E 4TH STREET • CINCINNATI, OHIO 45202 ° 513-369-5000 • FAX 513-723-2740
The number of persons authorized by
this power of attorney is not more than 24
No 0 21673
POWER OF ATTORNEY
KNOW ALL MEN BY THESE PRESENTS That the GREAT AMERICAN INSURANCE COMPANY a corporation organized and existing under
and by virtue of the laws of the State of Ohio, does hereby nominate, constitute and appoint the person or persons named below, each individually if more than
one is named its true and lawful attorney in fact, for it and in its name place and stead to execute on behalf of the said Company as surety, any and all bonds,
undertakings and contracts of suretyship, or other written obligations in the nature thereof, provided that the liability of the said Company on any such bond
undertaking or contract of suretyship executed under this authority shall not exceed the limit stated below
Name
JOHN HOPKINS JENNIFER LAKMANN KRISTIE PHILLIPS JASON MARCH
ELIZABETH COLLODI BRAD ESPINOSA CLAUDINE GORDIN MATTHEW FOSTER
SARA WALLISER JESSICA MONIUX MICHAEL K FEENEY SARAH OTTO
RENEE RAMSEY DEANNA QUINTERO SAMANTHA WATKINS MARY COLLINS
JOHN J WEBER K COREY WARD BILL RAPP PAULA SENNA
STEVEN L WILLIAMS MARISSA ROBINSON TONY CLARK PAMELA SEY
This Power of Attomey revokes all previous powers issued on behalf of the attorneys) -in -fact named above
IN WITNESS WHEREOF the GREAT AMERICAN INSURANCE COMPANY has caused these presents to be signed and attested by its appropriate
officers and its corporate seal hereunto affixed this 28TH day of JULY 2021
Attest GREAT AMERICAN INSURANCE COMPAN
Assistant Secretary
STATE OF OHIO COUNTY OF HAMILTON ss
On this 28TH day of JULY , 2021 , before me personally appeared MARK VICARIO to me known
being duly swom, deposes and says that he resides in Cincinnati, Ohio, that he is a Divisional Senior Vice President of the Bond Division of Great American
Insurance Company the Company descnbed in and which executed the above instrument that he knows the seal of the said Company that the seal affixed to the
said instrument is such corporate seal that it was so affixed by authority of his office under the By Laws of said Company and that he signed his name thereto
by like authority
Address
ALL OF CHICO,CALIFORNIA
Limit of Power
ALL
$100 000 000
Divisional Senior Vice President
SUSAN A KOHORST
Notary Public
State of Ohio
My Comm Expires
May 18, 2025
MARK VICARIO (877 377-2405)
22A-zet-e-acilL&Y
This Power ofAttorney is granted by authority of the following resolutions adopted by the Board of Directors of Great Amencan Insurance Company
by unanimous written consent dated June 9 2008
RESOLVED That the Divisional President the several Divisional Senior Vice Presidents Divisional Vice Presidents and Divisonal Assistant Vice
Presidents or any one of them, be and hereby is authorized, from time to time to appoint one or more Attorneys -in -Fact to execute on behalf of the Company,
as surety, any and all bonds, undertakings and contracts of suretyship or other written obligations in the nature thereof to prescribe their respective duties and
the respective limits of their authority, and to revoke any such appointment at any time
RESOLVED FURTHER That the Company seal and the signature of any of the aforesaid officers and any Secretary or Assistant Secretary of the
Company may be affixed by facsimile to any power of attorney or certificate of either given for the execution of any bond, undertaking contract of suretyship
or other written obligation in the nature thereof such signature and seal when so used being hereby adopted by the Company as the original signature of such
officer and the original seal of the Company, to be valid and binding upon the Company with the same force and effect as though manually affixed.
CERTIFICATION
I, STEPHEN C BERAHA Assistant Secretary of Great American Insurance Company, do hereby certify that the foregoing Power ofAttorney and
the Resolutions of the Board of Directors of June 9, 2008 have not been revoked and are now in full force and effect
Signed and sealed this
2nd day of
December , 2021
Assistant Secretary
S1029AH (03/20)
EXHIBIT "C"
PRICE AND FEE BID
Phase 2 (Fiscal Year 2021-2022)
2330 Booster Pump Station
Airport Well #1
Airport Well #2
Chicken Hill Well
Church Street Well
Coolie Hat Flow Monitor
Crafton Well
Hog Canyon Well #2
Madeira Well
Maguet Well #2
Mentone Acres Well #2
Mill Creek Well #2
Mill Creek Well #2A
Orange Street Well
Rees Well
Tate Water Treatment Plant
Well #38
Well #39
Contingency (10%) *
PHASE 2 SUBTOTAL.
Phase 3 (Fiscal Year 2022-2023)
Agate Well #1
California Street Well
Crescent & Crown Pressure Monitor
East Lugonia Well #3
East Lugonia Well #4
East Lugonia Well #6
Mentone & Crafton Valve Vault
Mill Creek Well #4
Muni Well
New York Street Well
Redlands Heights Well
Wabash & I-10 Pressure Monitor
Well #34
Contingency (10%) *
PHASE 3 SUBTOTAL.
GRAND TOTAL (Phases 2 & 3)
$134,050 00
$289,600 00
$152,950 00
$196,950 00
$130,400.00
$45,850 00
$211,750 00
$135,500 00
$152,850 00
$ 242, 600 00
$254,550 00
$155,700 00
$155,500 00
$164,550 00
$210,700 00
$373,300 00
$166,900 00
$171,500 00
$334,520 00
$3,679,720 00
$133, 600.00
$128,100.00
$72,250 00
$149, 050.00
$158,300.00
$155,150 00
$100,650 00
$162,800 00
$155,850 00
$125,050 00
$199,000 00
$86,500 00
$100,700 00
$172,700 00
$1,899,700.00
$5,579,420.00
* Contingency (1O%) Contingency will be used for unforeseen work not covered within all other tasks shall be made at the contract lump sum
price and shall constitute full compensation for all labor material, equipment, and incidentals required. Unforeseen work must be approved by
the City staff before doing any work, and pay estimate shall be negotiated based on unit price already established with the proposal for this
project. Any work required that is outside of the proposed cost, shall be performed based on time & material (T&M) basis and T&M cost shall be
negotiated and approved by the City staff prior to performing the work. Unforeseen work will be paid in each billing cycle with a percentage of
the lump sum cost included in the bid. This item may or may not be spent entirely
42
L.\ca\djm\Agreements\Tesco Controls Agreement.NPS-2.2.FY21-0044.doc.jn
EXHIBIT "D"
WORKERS' COMPENSATION INSURANCE CERTIFICATION
Every employer, except the State, shall secure the payment of compensation in one or more of
the following ways
A By being insured agamst liability to pay compensation by one or more insurers
duly authorized to write compensation msurance in this State
B By secunng from the Director of Industrial Relations, a certificate of consent to
self -insure, either as an individual employer, or as one employer in a group of
employers, which may be given upon furnishing proof satisfactory to the Director
of Industrial Relations of ability to self -insure and to pay any compensation that
may become due to his or her employees
CHECK ONE
i( I am aware of the provisions of Section 3700 of the Labor Code which requires every
employer to be insured against liability for Workers' Compensation or to undertake self-
insurance m accordance with the provisions of that Code, and I will comply with such provisions
before commencmg the performance of the work and activities required or permitted under this
Agreement (Labor Code §1861)
I affirm that at all times, in performing the work and activities required or permitted under
this Agreement, I shall not employ any person in any manner such that I become subject to the
workers' compensation laws of California However, at any time, if I employ any person such
that I become subject to the workers' compensation laws of California, immediately I shall
provide the City with a certificate of consent to self -insure, or a certification of workers'
compensation insurance
I certify under penalty of perjury under the laws of the State of California that the mfoiluation
and representations made m this certificate are true and correct
TESCO C9LS, INC
By
Shain Thomas, CEO
43
L \ca\djm\Agreements\Tesco Controls Agreement.NPS 2.2.FY21 0044.doc..n
Date